Zenith Turntables | Drive Belts and Idler Wheels

Turntable Tuneup has everything you need to bring your Zenith turntable up to speed and tuned up properly.  We also have a wide selection of turntable accessories like cartridge alignment tools, stylus force gauges, record brushes, silicone damping fluid and more.  Some of these items can be seen at the bottom of this page, or follow the menu bar for the complete selection.

Replacing the drive belt is usually all you need to do to restore proper speed and speed stability to your turntable.  Old belts will stretch out, wear and lose friction, resulting in slow speed, and noticeable wow and flutter during playback.  Unstable platter speed can also harm sound quality even when you can’t hear a noticeable variation in pitch.  Replacing the belt is easy; just remove the platter, and the new belt will fit snugly around the flange on its underside.  Then put the platter back in place and turn it until the motor spindle is visible through one of the holes in the platter.  Then, use a paperclip to pull the belt over the motor spindle, and you’re done!

Removing an idler wheel should be a very straightforward matter of pulling up on the hub of the disk while holding back against the spindle or its frame, though some are held in place with clips that are easily removed with a flat screwdriver. Visit the Idler Wheel Page for more information.

If your turntable is not listed, then it’s easy to determine the correct size of your belt by measuring the circumference of the original belt and deducting 3 to 5 percent.  If the original belt is missing or broken, you can measure the circumference of the belt drive flange on the underside of the platter, and deduct 2 to 3 percent.  All belt model numbers include the circumference in inches.  We have a few hundred different belt models in stock: flat, square cut and round o-rings.


Zenith 3WGR-50

Platter Drive Belt: O-Ring Belt, Model OA 7.0.  Circumference: 7.034 in (179 mm). Thickness: 0.070 in (1/16 in) (1.78 mm).

7.0 Inch O-Ring Turntable Drive Belt
Turntable Drive Belt OA 7.0
Click on Photo for Larger Version.

Platter Drive Belt
OA 7.0 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 3WGR-52

Platter Drive Belt: O-Ring Belt, Model OA 7.0.  Circumference: 7.034 in (179 mm). Thickness: 0.070 in (1/16 in) (1.78 mm).

7.0 Inch O-Ring Turntable Drive Belt
Turntable Drive Belt OA 7.0
Click on Photo for Larger Version.

Platter Drive Belt
OA 7.0 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 3WGR-54

Platter Drive Belt: O-Ring Belt, Model OA 7.0.  Circumference: 7.034 in (179 mm). Thickness: 0.070 in (1/16 in) (1.78 mm).

7.0 Inch O-Ring Turntable Drive Belt
Turntable Drive Belt OA 7.0
Click on Photo for Larger Version.

Platter Drive Belt
OA 7.0 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 5WFR-50

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 12WFR-51

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 12WFR-51

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-149

Platter Drive Belt: Flat Medium Belt, Model FM 20.7.  Circumference: 20.7 Inches (526 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

20.7 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 20.7
Click on Photo for Larger Version.

Platter Drive Belt
FM 20.7 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-154

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-159

Platter Drive Belt: Flat Medium Belt, Model FM 20.7.  Circumference: 20.7 Inches (526 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

20.7 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 20.7
Click on Photo for Larger Version.

Platter Drive Belt
FM 20.7 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-195

Platter Drive Belt: Flat Medium Belt, Model FM 21.6.  Circumference: 21.6 Inches (549 mm).  Width: 0.178 inches (3/16 in) (4.5 mm).  Thickness: 0.024 in (1/64 in) (0.6 mm).

21.6 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 21.6
Click on Photo for Larger Version.

Platter Drive Belt
FM 21.6 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-228

Platter Drive Belt: Flat Medium Belt, Model FM 21.6.  Circumference: 21.6 Inches (549 mm).  Width: 0.178 inches (3/16 in) (4.5 mm).  Thickness: 0.024 in (1/64 in) (0.6 mm).

21.6 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 21.6
Click on Photo for Larger Version.

Platter Drive Belt
FM 21.6 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-250

Platter Drive Belt: Flat Medium Belt, Model FM 22.4.  Circumference: 22.4 Inches (569 mm).  Width: 0.188 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

22.4 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 22.4
Click on Photo for Larger Version.

Platter Drive Belt
FM 22.4 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-335

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-335

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-336

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-336

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-337

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-337

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-338

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-341

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-341

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-342

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-342

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-343

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-343

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-485

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-485

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-486

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-486

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-487

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-487

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-487

Platter Drive Belt: Flat Medium Belt, Model FM 11.5.  Circumference: 11.5 Inches (292 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.5 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.5
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-490

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-557

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-558

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-559

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-571

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-574

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-574-01

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-579

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-586

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-588

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 169-588

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith 4175

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith Cobra-Matic

Platter Drive Belt: Flat Medium Belt, Model FM 8.9.  Circumference: 8.9 Inches (226 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

8.9 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 8.9
Click on Photo for Larger Version.

Platter Drive Belt
FM 8.9 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith ET-915-P3

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith F-587W

Platter Drive Belt: Flat Medium Belt, Model FM 11.5.  Circumference: 11.5 Inches (292 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.5 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.5
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith G-941P

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith G-942M

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith G-946AE/AES

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith GR-901-P1

Platter Drive Belt: Flat Medium Belt, Model FM 9.7.  Circumference: 9.7 Inches (246 mm).  Width: 0.187 inches (3/16 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

9.7 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 9.7
Click on Photo for Larger Version.

Platter Drive Belt
FM 9.7 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith GR-937P

Platter Drive Belt: Flat Medium Belt, Model FM 11.5.  Circumference: 11.5 Inches (292 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.5 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.5
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith HPS-45

Platter Drive Belt: Flat Medium Belt, Model FM 11.3.  Circumference: 11.3 Inches (287 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

11.3 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 11.3
Click on Photo for Larger Version.

Platter Drive Belt
FM 11.3 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith HPS-45

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith HR-596W

Platter Drive Belt: Flat Medium Belt, Model FM 9.7.  Circumference: 9.7 Inches (246 mm).  Width: 0.187 inches (3/16 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

9.7 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 9.7
Click on Photo for Larger Version.

Platter Drive Belt
FM 9.7 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith HR-966P

Platter Drive Belt: Flat Medium Belt, Model FM 8.9.  Circumference: 8.9 Inches (226 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

8.9 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 8.9
Click on Photo for Larger Version.

Platter Drive Belt
FM 8.9 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith IS-4021

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith IS-4031

Device Control Belt: Square-Cut Belt, Model SCX 9.5.  Circumference: 9.5 inches (241 mm).  Width: 0.046 inches (3/64 in) (1.2 mm).  Thickness: 0.046 in (3/64 in) (1.2 mm).

9.5 Inch Square-Cut Turntable Drive Belt
Turntable Drive Belt SCX 9.5
Click on Photo for Larger Version.

Device Control Belt
SCX 9.5 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith IS-4041

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith IS-4041

Device Control Belt: Square-Cut Belt, Model SCX 9.5.  Circumference: 9.5 inches (241 mm).  Width: 0.046 inches (3/64 in) (1.2 mm).  Thickness: 0.046 in (3/64 in) (1.2 mm).

9.5 Inch Square-Cut Turntable Drive Belt
Turntable Drive Belt SCX 9.5
Click on Photo for Larger Version.

Device Control Belt
SCX 9.5 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith IS-4081

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith IS-4090

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-902P/P1

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-912AE

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-915P

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-915P1

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-915P1

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-915P2

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-915P2

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-916PN

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-916PN1

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-916PN1

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-919P

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-919P

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-919P1

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-919P1

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-920AE

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith LR-920AE

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith M-900P

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith M-902P

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MC-9025

Device Control Belt: Square-Cut Belt, Model SM 13.0.  Circumference: 13.0 inches (330 mm).  Width: 0.046 inches (3/64 in) (1.2 mm).  Thickness: 0.078 in (3/64 in) (1.2 mm).

13.0 Inch Square-Cut Turntable Drive Belt
Turntable Drive Belt SM 13.0
Click on Photo for Larger Version.

Device Control Belt
SM 13.0 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MC-9030

Platter Drive Belt: Flat Medium Belt, Model FM 16.8.  Circumference: 16.8 Inches (427 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

16.8 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 16.8
Click on Photo for Larger Version.

Platter Drive Belt
FM 16.8 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MC-9030

Belt GT 10.3

Unavailable


Zenith MC-9040

Platter Drive Belt: Flat Medium Belt, Model FM 16.8.  Circumference: 16.8 Inches (427 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

16.8 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 16.8
Click on Photo for Larger Version.

Platter Drive Belt
FM 16.8 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MC-9040

Belt GT 12.9

Unavailable


Zenith MD-912AE

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MD-919P

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MD-919P

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith ML-2670

Platter Drive Belt: Flat Medium Belt, Model FM 20.7.  Circumference: 20.7 Inches (526 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

20.7 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 20.7
Click on Photo for Larger Version.

Platter Drive Belt
FM 20.7 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MM-2670

Platter Drive Belt: Flat Medium Belt, Model FM 23.2.  Circumference: 23.2 Inches (589 mm).  Width: 0.188 inches (3/16 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

23.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 23.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 23.2 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MR-915P

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MR-916PN

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MR-917M

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MR-920AE

Platter Drive Belt: Flat Medium Belt, Model FRM 10.5.  Circumference: 10.5 Inches (267 mm).  Width: 0.210 inches (7/32 in) (5 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

Flat Turntable Drive Belt, Circumference: 10.5 Inches; Width: 0.210 Inches; Thickness: 0.031 Inches.
Turntable Drive Belt FRM 10.5
Click on Photo for Larger Version.

Platter Drive Belt
FRM 10.5 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith MR-920AE

Platter Drive Belt: Flat Medium Belt, Model FM 15.2.  Circumference: 15.2 Inches (386 mm).  Width: 0.196 inches (3/16 in) (5 mm).  Thickness: 0.027 in (1/32 in) (0.7 mm).

15.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 15.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 15.2 $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith S-14067

Platter Drive Belt: Flat Medium Belt, Model FM 9.2.  Circumference: 9.2 Inches (234 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

9.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 9.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 9.2 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith S-14068

Platter Drive Belt: Flat Medium Belt, Model FM 9.2.  Circumference: 9.2 Inches (234 mm).  Width: 0.200 inches (3/16 in) (5 mm).  Thickness: 0.023 in (3/128 in) (0.6 mm).

9.2 Inch Flat Turntable Drive Belt
Turntable Drive Belt FM 9.2
Click on Photo for Larger Version.

Platter Drive Belt
FM 9.2 $5.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith S-53315

Platter Drive Belt: Flat Narrow Belt, Model FRZ 20.5  Circumference: 20.5 Inches (521 mm).  Width: 0.118 inches (1/8 in) (3 mm).  Thickness: 0.031 in (1/32 in) (0.8 mm).

20.5 Inch Flat Turntable Drive Belt
Turntable Drive Belt FRZ 20.5
Click on Photo for Larger Version.

Platter Drive Belt
FRZ 20.5 $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Zenith VM-24428

This turntable is driven by an idler wheel, which can be rebuilt. Send in your original idler wheel for service. Turnaround time is about four weeks. The rubber rim is replaced with new material and re-shaped. Does not include bronze hub re-machining.  Click Here for more information on our idler wheel rebuilding service.

Single Disk Idler Wheel
Single Disk Idler Wheel
Click On Image For Larger Version

Single Disk Idler Wheel Rebuilding Service $40.00


options



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Silicone Damping Fluid for Tonearm Cueing Mechanisms.

If the needle drops more quickly than you’d like when you drop the lever that raises and lowers the tonearm, then the damping fluid in the mechanism’s cylinder needs to be cleaned out and replaced.  Disassembly is straightforward: remove the tonearm rest, and then the cap on top of the cylinder.  Then you can pull the piston straight out, clean out the cylinder with a cotton swab, and add fresh fluid in small increments until original and proper operation is restored.  This thick damping fluid comes in a 10 cc syringe for easy application, and is a sufficient quantity to service several turntables.  It comes with complete instructions.  We have five different thicknesses of silicone in stock, to service monopivot damping wells and tonearm motion damping troughs.  Go to the silicone page for more options and information.

Tonearm Cueing Mechanism
Tonearm Cueing Mechanism

Cueing mechanism with cap removed from cylinder
Cueing mechanism with cap removed from cylinder
 Silicone300K

Silicone Damping Fluid 300,000 cSt, 10cc. $10.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Phono Cartridge Alignment Tool for 12 Inch Records.

This is essential for installing new cartridges and needles, or checking the setup of your old cartridge is aligned correctly.  Go the the Cartridge Alignment Page for more details and options. We have alignment tools for 7, 10, 12 and 16 inch records, in both Baerwald and Löfgren-B geometries.

 cropped-12inchalign-5.png

Phono Cartridge Alignment Tool for 12 Inch Records $20.00


Spindle Size



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Phono Cartridge Alignment Tool for 7 Inch Records.

For collectors of 45 RPM Singles, it is best to have an extra headshell and cartridge that are set up for the different effective length and offset angle requirements of the narrow playing band of 7 inch records.  Playing a 7 inch record on a turntable aligned for 7 inch instead of 12 inch records will bring down the maximum angular error and the average angular error by a ratio of more than 6 to 1.

 7inchalign-4

Phono Cartridge Alignment Tool for 7 Inch Records $20.00


Spindle Size



Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Stylus Force Gauge.

If your tonearm does not have a dial indicator on the counterweight for setting the tracking force (usually 1.5 grams), this handy stylus force gauge is essential for running your cartridge at the correct tracking weight.  Designed, manufactured and hand-calibrated in the USA, this force gauge is super-easy to use.  Just place the stylus inside the laser-etched line for the tracking force you desire.  The gauge has two small nubs on the bottom on which it pivots.  If the tracking force is too light, the far side will remain down.  If it’s too heavy, the stylus side of the gauge will bottom out.  If the stylus force is correct, the gauge will balance evenly on the two nubs.  It has etched lines for 1.0, 1.25, 1.5, 2, 2.5, 3, 3.5, 4, 4.5 and 5 grams.

 forcegauge1  forcegauge3
 forcegauge2

Stylus Force Gauge $15.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express


Carbon Fiber Record Brush.

A basic part of any record collector’s kit.  This brush has more than a million tiny conductive carbon fiber bristles which reach deep into the record grooves and cling to tiny dust particles.  Static charges hold the dust onto the bristles until they are swept off of the record; the brush can be cleaned off by rotating it in the frame; there is a tiny rib in the frame which will knock the dust off.  Do not touch the bristles with your fingers or use the brush in combination with any liquids.  The static cling which attracts dust to the brush works best when your body is electrically grounded; you should touch one hand to the turntable deckplate while using the other hand to sweep off the dust.  More cleaning supplies, including record cleaning fluid and cloths, and stylus cleaning kits, are available on the Cleaning Supplies Page.

Carbon Fiber Record Brush
Carbon Fiber Record Brush

Carbon Fiber Record Brush $12.00




Shopping Cart Supports Paypal, Visa, MasterCard, and American Express